remap@hdi-tuning.co.uk Contact us Book appointment
Siemens SID803 SID803A remap

2.0D 16V 136 BHP 2005 to 2010 Siemens SID803 SID803A

2006–2010 2.0D 16V 136 Diesel Siemens SID803 SID803A
Stock 136BHP 320Nm
Stage 1 180BHP 380Nm
Gain +44BHP +60Nm
Power (BHP) Torque (Nm) Stock Stage 1 dyno
225 450 180 360 135 270 90 180 45 90 0 0 10002000300040005000 RPM 380 Nm 180 BHP
Recommended tool Dimsport MyGenius: flash this car over OBD yourself
Stage 1 remap incl. OBD programming tool £330
Buy now · £330
  1. 1Read ECU over OBD
  2. 2Files sent by email
  3. 3Program yourself
  • All tuning is developed in house - over 15 years of experience
S1

Stage 1

180BHP+44
380Nm+60
Our Stage 1 remap gives 180BHP and a torque increase to 380Nm. We've developed this remap not only to give optimal performance, but also to remain within the limits of the stock hardware of your vehicle so you don't need to worry about your clutch or your dual mass flywheel. Power delivery will be smooth and constant through the entire rpm range and will make overtaking much easier.
Stage 1 vs stock
Power +32%
136 180 BHP
Stock 136S1 180 (+44)
Torque +19%
320 380 Nm
Stock 320S1 380 (+60)
See the dyno chart ↑
S2

Stage 2

195BHP+59
395Nm+75
The Stage 2 remap requires an uprated intercooler, complete free flowing exhaust system and a 3.1 Bar MAP sensor (part number PS10197) so that the ECU is able to run increased turbo pressure.

Peak power comes out at 195 BHP with a torque figure of 380 to 400Nm depending on your exact setup. Exhaust upgrades help a lot for the Stage 2 remap.
Power (BHP) Torque (Nm) Stock Stage 2 dyno
225 500 180 400 135 300 90 200 45 100 0 0 10002000300040005000 RPM 395 Nm 195 BHP
S3

Stage 3

210BHP+74
420Nm+100
The stage 3 remap requires all the stage 2 modifications and also a hybrid turbo. The turbo charger should use an upgraded 52mm billet compressor wheel. This will allow the turbo to flow more air whilst remaining suitably matched to the original turbine wheel and can also be controlled by the ECU software more easily than a complete upgraded turbo. By using a 52mm compressor there will not be large change in turbo lag. The fuel pump is the limit on this remap, it will struggle to flow more than 210 BHP of fuel. An additional in tank lift pump to feed the high pressure pump can be helpful, it’s also essential the fuel pump is in excellent condition, if it’s worn it will need to be refurbished. For this level of torque, it’s best to use a Ceramic paddle clutch with a solid flywheel.
Power (BHP) Torque (Nm) Stock Stage 3 dyno
250 500 200 400 150 300 100 200 50 100 0 0 10002000300040005000 RPM 420 Nm 210 BHP
Siemens SID803 SID803A

Programming method

Programming Methods – OBD - MyGenius

Program from home over OBD using MyGenius. The only equipment you need is a battery charger to keep the vehicle power stable. A laptop is required to initialise the MyGenius tool, it is not used during programming. The tool is standalone and powered from the OBD port.

Programming Methods – OBD - MPPS

This ECU can be OBD programmed with MPPS

Programming Methods – OBD - Kess

This ECU can be OBD programmed with Kess
More Volvo

Other Volvo remaps