remap@hdi-tuning.co.uk Contact us Book appointment
Bosch EDC17C60 remap

1.6 BlueHDI 8V 100 BHP 2015 – 2019 Bosch EDC17C60 EU6 ProAce

2015–2019 1.6 BlueHDI 8V 100 Diesel Bosch EDC17C60
Stock 100BHP 254Nm
Stage 1 130BHP 330Nm
Gain +30BHP +76Nm
Power (BHP) Torque (Nm) Stock Stage 1 dyno
150 400 120 320 90 240 60 160 30 80 0 0 10002000300040005000 RPM 330 Nm 130 BHP
Recommended tool Dimsport MyGenius: flash this car over OBD yourself
Stage 1 remap incl. OBD programming tool £330
Buy now · £330
  1. 1Read ECU over OBD
  2. 2Files sent by email
  3. 3Program yourself
  • All tuning is developed in house - over 15 years of experience
S1

Stage 1

130BHP+30
330Nm+76
The Stage 1 Remap is designed to run safely on a standard vehicle and does not need any modifications. With a Stage 1 remap your power goes up to 130BHP and torque to 330Nm, the gains are huge! This remap is designed to run with the DPF in place and is road legal.

Here's a dyno plot showing the Stage 1 remap applied to the 1.6 BlueHDI 100HP engine.
Stage 1 vs stock
Power +30%
100 130 BHP
Stock 100S1 130 (+30)
Torque +30%
254 330 Nm
Stock 254S1 330 (+76)
See the dyno chart ↑
S3.1

Stage 3 · Option 1

GTD12 upgrade

150BHP+50
345Nm+91
When you upgrade to the turbo from the 1.6 120 engine we can remap the ECU to 150 BHP and 345Nm of Torque.

You must not drive the vehicle until the ECU is remapped to suit, the VNT control needs to be activated in order to safely control boost pressure.

We've carried out this remap lots of times on the EDC17C60 ECU and we have a fully working and tested solution.

The turbo position sensor does not need to be re-wired on the bluehdi the pinout is the same. This is a very easy upgrade, you can use all the pipework from the 120 engine.
Power (BHP) Torque (Nm) Stock Stage 3 · Option 1 dyno
175 400 140 320 105 240 70 160 35 80 0 0 10002000300040005000 RPM 345 Nm 150 BHP
S3.2

Stage 3 · Option 2

GTD12 Hybrid turbo

180BHP+80
370Nm+116
Our Stage 3 remap uses a GTD1244VZ 819872 49mm hybrid turbo with 52mm extended tips.

You need an intercooler and exhaust upgrade, also the clutch will need to be uprated.

The hybrid turbo is not for everyone, the trade off of more top end power is that you’re going to lose some low end torque because the larger compressor wheel takes slightly longer to spool up, although with the billet compressor wheel this is not drastic.

Please note: For any Hybrid upgrade you need to use the hybrid turbo built by HDI Tuning, otherwise we will not be able to offer a remap to match the setup. Every turbo is made different and we can’t offer a solution that fits them all, lots of development work is required for a setup like this.

This setup can be run with the DPF in place, you'll come out closer to 170 BHP with that setup as the DPF acts as a bottleneck when tuning.
Power (BHP) Torque (Nm) Stock Stage 3 · Option 2 dyno
225 450 180 360 135 270 90 180 45 90 0 0 10002000300040005000 RPM 370 Nm 180 BHP
Bosch EDC17C60

Programming method

Programming Methods – OBD - MyGenius

Program from home over OBD using MyGenius. The only equipment you need is a battery charger to keep the vehicle power stable. A laptop is required to initialise the MyGenius tool, it is not used during programming. The tool is standalone and powered from the OBD port.

When you receive the tool, scan the QR code to download the software.
Connect the tool via USB to your computer and initialise the tool.
Now connect your battery charger to the vheicle battery, MyGenius to the OBD port.
Follow the on screen instructions to extract the data from the ECU.
Connect to the PC, send us the file, we remap and send it back.
Add the file to the tool with the computer, move back to the car and connect charger, connect MyGenius to the OBD port.
Follow the on screen instructions to program the ECU.

Programming via Bench service mode

Bosch EDC16 and EDC17 ECUs can be programmed in bench service mode without opening the ECU. This is the method we use when you send us your ECU using the postal remapping service. A full backup can be made of both the EEPROM and the internal flash memories.

Programming via BDM port or Boot mode with bench tool.

This is an old method with an open ECU, a boot pin must be connected to the board. We avoid this except for recovery when there is no comms in bench service mode.
More Toyota

Other Toyota remaps