Bosch EDC17C10 remap
1.6 HDI 8V 92 DPF 2010 – 2015 Bosch EDC17C10 EU5 Peugeot Partner
2010–2015 1.6 HDI 8V 92 Diesel Bosch EDC17C10
Stock 92BHP 230Nm
Stage 1 121BHP 290Nm
Gain +29BHP +60Nm
Stage 1 remap incl. OBD programming tool £330
Buy now · £330 - 1Read ECU over OBD
- 2Files sent by email
- 3Program yourself
- All tuning is developed in house - over 15 years of experience
S1
Stage 1
121BHP+29
290Nm+60
The Stage 1 Remap is designed to run safely on a standard car and does not need any modifications. Power goes to an impressive 121BHP and torque to a strong 290Nm.
This remap is designed to run with the DPF in place and is road legal. Power delivery is smooth and progressive, you'll love the way your car drives with a stage 1 remap.
Stage 1 vs stock See the dyno chart ↑
Power +32%
92 121 BHP
Stock 92S1 121 (+29)
Torque +26%
230 290 Nm
Stock 230S1 290 (+60)
S1+
Stage 1+
With Exhaust Upgrade
126BHP+34
300Nm+70
The Stage 1+ Remap is designed to run with a performance exhaust system with a down pipe fitted and for optimal power a full straight through system.
Stage 1+ vs stock
Power92 → 126 BHP
Torque230 → 300 Nm
Dyno graph for this stage coming soon.
S2
Stage 2
130BHP+38
310Nm+80
The stage 2 remap requires an upgraded intercooler and also an upgraded exhaust system. The intercooler should be as large as you can fit behind the bumper, this makes a big difference on the 1.6 8v engine as we found the intercooler to suffer from heat soak when run consistently hard or on a dyno.
The exhaust can be 2.5 inch all the way through with a free flowing type silencer.
This remap can be ran with the DPF intact, we did extensive testing with this heavier remap and found that it worked well with the DPF in place. You must still do regular long journeys so it can regenerate properly.
It is important that your DPF is relatively clean, with a low soot % of 40% or less, if the DPF is blocked already you will get less power and the DPF will load up faster as this remap is heavier than the stage 1 remap.
The exhaust can be 2.5 inch all the way through with a free flowing type silencer.
This remap can be ran with the DPF intact, we did extensive testing with this heavier remap and found that it worked well with the DPF in place. You must still do regular long journeys so it can regenerate properly.
It is important that your DPF is relatively clean, with a low soot % of 40% or less, if the DPF is blocked already you will get less power and the DPF will load up faster as this remap is heavier than the stage 1 remap.
S3
Stage 3
GTD1244VZ Turbo upgrade
150BHP+58
330Nm+100
We are able to offer a VNT turbo upgrade which works on the factory ECU with minimal work required. The turbo comes from the 1.6 BlueHDI 120 or 1.5 TDCI 120. The turbo model is GTD1244VZ and you MUST use part number 819872. An intercooler and Straight through exhaust system is essential for this setup.
You cannot run this turbo upgrade without a remapping the ECU and you can't drive with it fitted until the software is adjusted. It’s best to fit the turbo once you have the software ready to program to the ECU. The normal approach is to order a MyGenius tool, read out the ECU and get the Stage 3 remap prepared by us, then you can fit the turbo afterwards without needing to drive to a tuning shop.
On fords you will need to change all three wires to the turbo position sensor, on PSA vehicles you usually need to swap pins 1/3 on the turbo positon sensor. Click here for PDF of build guide
We DO NOT offer a hybrid GTD12 remap for 1.6 8v vehicles with the EDC17C10 ECU. The fuel pump will not flow more than 150 BHP, so do not fit a a hybrid GTD12 turbo, you will not get more power.
You cannot run this turbo upgrade without a remapping the ECU and you can't drive with it fitted until the software is adjusted. It’s best to fit the turbo once you have the software ready to program to the ECU. The normal approach is to order a MyGenius tool, read out the ECU and get the Stage 3 remap prepared by us, then you can fit the turbo afterwards without needing to drive to a tuning shop.
On fords you will need to change all three wires to the turbo position sensor, on PSA vehicles you usually need to swap pins 1/3 on the turbo positon sensor. Click here for PDF of build guide
We DO NOT offer a hybrid GTD12 remap for 1.6 8v vehicles with the EDC17C10 ECU. The fuel pump will not flow more than 150 BHP, so do not fit a a hybrid GTD12 turbo, you will not get more power.
Bosch EDC17C10
Programming method
Programming Methods – OBD - MyGenius
Program from home over OBD using MyGenius. The only equipment you need is a battery charger to keep the vehicle power stable.
A laptop is required to initialise the MyGenius tool, it is not used during programming. The tool is standalone and powered from the OBD port.
When you receive the tool, scan the QR code to download the software.
Connect the tool via USB to your computer and initialise the tool.
Now connect your battery charger to the vheicle battery, MyGenius to the OBD port.
Follow the on screen instructions to extract the data from the ECU.
Connect to the PC, send us the file, we remap and send it back.
Add the file to the tool with the computer, move back to the car and connect charger, connect MyGenius to the OBD port.
Follow the on screen instructions to program the ECU.
When you receive the tool, scan the QR code to download the software.
Connect the tool via USB to your computer and initialise the tool.
Now connect your battery charger to the vheicle battery, MyGenius to the OBD port.
Follow the on screen instructions to extract the data from the ECU.
Connect to the PC, send us the file, we remap and send it back.
Add the file to the tool with the computer, move back to the car and connect charger, connect MyGenius to the OBD port.
Follow the on screen instructions to program the ECU.
Programming via Bench service mode
Bosch EDC16 and EDC17 ECUs can be programmed in bench service mode without opening the ECU. This is the method we use when you send us your ECU using the postal remapping service. A full backup can be made of both the EEPROM and the internal flash memories.
Programming via BDM port or Boot mode with bench tool.
This is an old method with an open ECU, a boot pin must be connected to the board. We avoid this except for recovery when there is no comms in bench service mode.
More Peugeot
Other Peugeot remaps
Stage 1 incl. tool £330 Buy now