remap@hdi-tuning.co.uk Contact us Book appointment
Bosch EDC15C2 remap

2.0 HDI 8v 16v 110BHP DPF 2002 - 2006 Bosch EDC15C2 Peugeot 807

2002–2006 2.0 HDI 8v 16v 110 Diesel Bosch EDC15C2
Stock 110BHP 250Nm
Stage 1 140BHP 300Nm
Gain +30BHP +50Nm
Power (BHP) Torque (Nm) Stock Stage 1 dyno
175 350 140 280 105 210 70 140 35 70 0 0 2000300040005000 RPM 300 Nm 140 BHP
Recommended tool Dimsport MyGenius: flash this car over OBD yourself
Stage 1 remap incl. OBD programming tool £330
Buy now · £330
  1. 1Read ECU over OBD
  2. 2Files sent by email
  3. 3Program yourself
  • All tuning is developed in house - over 15 years of experience
S1

Stage 1

DPF Safe Remap

140BHP+30
300Nm+50
The Peugeot 807 2.0 HDI 110 DPF safe remap is specially designed by HDI Tuning and tested over many years to ensure maximum power from a stage 1 remap whilst minimising the risk of DPF blockage. To do this we keep AFR high and clean this reduces soot particles and thus soot accumulation in the DPF. The Stage 1 DPF safe remap still gives great gains with 140 BHP and 300Nm. We recommend this remap for vehicles that are well maintained and cover plenty of long journeys to keep the DPF clean.
Stage 1 vs stock
Power +27%
110 140 BHP
Stock 110S1 140 (+30)
Torque +20%
250 300 Nm
Stock 250S1 300 (+50)
See the dyno chart ↑
S1+

Stage 1+

145BHP+35
320Nm+70
The Stage 1 + remap is designed for optimum performance and reliability on a vehicle fitted with a sports exhaust. Peak power will be 145 BHP and maximum torque will be increased to an exciting 320Nm. The stage 1 remap is designed to run clean with no smoke on engines that are well maintained. If your engine is old and worn it's better to choose the lower power remap. Our remap for the Peugeot 807 2.0 HDI 110 delivers optimal power by matching the air delivered by the turbo to the correct quantity of diesel throughout the rev range of the engine. The result of this is great progressive power that keeps on pulling until 4000 rpm and a bit more too. As well as a great power boost you can expect to see economy gains of 3-5 MPG on average.
Power (BHP) Torque (Nm) Stage 1+ dyno
175 400 140 320 105 240 70 160 35 80 0 0 2000300040005000 RPM 320 Nm 146 BHP
S2

Stage 2

160BHP+50
365Nm+115
The next stage in tuning requires a large front mounted intercooler. It’s best to fit a larger cooler, the limit is the space available behind the bumper. As boost pressure will be increased, a higher reading 3.1 Bar MAP sensor must be fitted so that the ECU can regulate boost at a higher pressure, the 3.1 Bar MAP sensor uses part number 9649396580. To help with EMP the exhaust needs to be a straight through system, 2.5 inch is best. Most vehicles will require a new clutch or an upgraded Kevlar clutch to handle the extra torque. With 365Nm there will really be a big difference in power and torque and how it’s delivered.
Power (BHP) Torque (Nm) Stage 2 dyno
200 450 160 360 120 270 80 180 40 90 0 0 2000300040005000 RPM 360 Nm 155 BHP
S3

Stage 3

180BHP+70
420Nm+170
The stage 3 remap requires all of the Stage 2 upgrades, and also a turbo upgrade. The fuel pump must be upgraded to the R70 pump from a 2.2 HDI or a 3.0 BMW 530D. It’s important to use a good low mileage pump and not one that has been left standing without fuel in as the pump can corrode inside and cease, thus damaging the seals once it’s turned. The fuel pressure sensor 1920GW must be fitted, to get the engine to run with this pins 1&2 must be swapped in the wiring loom to the sensor. The turbo upgrade would ideally use a 52mm compressor with a VNT turbo, although a waste-gated turbo is also acceptable and easier to regulate with a mechanical boost controller. The electronic turbo control will be de-activated in the ecu software to avoid setup complications and to allow for external regulation. For VNT turbos the turbo can be controlled using a product called DigiBooster S. This uses electronic PID control to regulate boost with selectable strategies, a VNT turbo cannot be effectively controlled using only a ball and spring type mechanical boost controller. A ceramic paddle clutch is required to hold the 420Nm of torque.
Stage 3 vs stock
Power110 → 180 BHP
Stock
S3
Torque250 → 420 Nm
Stock
S3

Dyno graph for this stage coming soon.

Peugeot 807 2.0 HDI 110 Stage 1 + Full power Remap ( 150 BHP | 330 Nm )

The Stage 1++ remap adds to the gains of the stage 1+ remap and requires a complete straight through exhaust system and a high flow air filter. Peak power will be increased to 150 BHP and the maximum torque will be increased to 330Nm. Price:

1800 Bar fuel pressure sensor upgrade Part 1920GW

For vehicles running the upgraded R70 fuel pump wishing to push for a little extra top end power we can increase fuel pressure slightly. The stock sensor can only go to 1500 Bar so an upgraded sensor is required with part number 1920GW. Pins 1&2 must be swapped in the wiring loom in order to start the engine and a new calibration must be added via a remap. Injector calibrations in the stock ECU software run only until 1400 Bar, we will extend using our custom calibrations to 1800 bar. We recommend to run a max of 1600 Bar even with the uprated sensor, otherwise the extra work load on the fuel pump is too much. Price:
  • £50 extra on top of remap cost – included with stage 3.
Bosch EDC15C2

Programming method

Programming Methods – OBD - MyGenius

Program from home over OBD using MyGenius. The only equipment you need is a battery charger to keep the vehicle power stable. A laptop is required to initialise the MyGenius tool, it is not used during programming. The tool is standalone and powered from the OBD port.

Programming Methods – OBD - MPPS

This ECU can be OBD programmed with MPPS

Programming Methods – OBD - Kess

This ECU can be OBD programmed with Kess
More Peugeot

Other Peugeot remaps