Bosch EDC15C2 remap
2.0 HDI 8v 110BHP DPF 2000 - 2005 Bosch EDC15C2 Peugeot 607
2000–2005 2.0 HDI 8v 110 Diesel Bosch EDC15C2
Stock 110BHP 250Nm
Stage 1 140BHP 300Nm
Gain +30BHP +50Nm
Stage 1 remap incl. OBD programming tool £330
Buy now · £330 - 1Read ECU over OBD
- 2Files sent by email
- 3Program yourself
- All tuning is developed in house - over 15 years of experience
S1
Stage 1
DPF Safe Remap
140BHP+30
300Nm+50
The Peugeot 607 2.0 HDI 110 DPF safe remap is specially designed by HDI Tuning and tested over many years to ensure maximum power from a stage 1 remap whilst minimising the risk of DPF blockage. To do this we keep AFR high and clean this reduces soot particles and thus soot accumulation in the DPF. The Stage 1 DPF safe remap still gives great gains with 140 BHP and 300Nm. We recommend this remap for vehicles that are well maintained and cover plenty of long journeys to keep the DPF clean.
Stage 1 vs stock See the dyno chart ↑
Power +27%
110 140 BHP
Stock 110S1 140 (+30)
Torque +20%
250 300 Nm
Stock 250S1 300 (+50)
S1+
Stage 1+
145BHP+35
320Nm+70
The Stage 1 + remap is designed for optimum performance and reliability on a vehicle fitted with a sports exhaust. Peak power will be 145 BHP and maximum torque will be increased to an exciting 320Nm. The stage 1 remap is designed to run clean with no smoke on engines that are well maintained. If your engine is old and worn it's better to choose the lower power remap. Our remap for the Peugeot 607 2.0 HDI 110 delivers optimal power by matching the air delivered by the turbo to the correct quantity of diesel throughout the rev range of the engine. The result of this is great progressive power that keeps on pulling until 4000 rpm and a bit more too. As well as a great power boost you can expect to see economy gains of 3-5 MPG on average.
S2
Stage 2
160BHP+50
365Nm+115
The next stage in tuning requires a large front mounted intercooler. It’s best to fit a larger cooler, the limit is the space available behind the bumper. As boost pressure will be increased, a higher reading 3.1 Bar MAP sensor must be fitted so that the ECU can regulate boost at a higher pressure, the 3.1 Bar MAP sensor uses part number 9649396580. To help with EMP the exhaust needs to be a straight through system, 2.5 inch is best. Most vehicles will require a new clutch or an upgraded Kevlar clutch to handle the extra torque. With 365Nm there will really be a big difference in power and torque and how it’s delivered.
S3
Stage 3
180BHP+70
420Nm+170
The stage 3 remap requires all of the Stage 2 upgrades, and also a turbo upgrade. The fuel pump must be upgraded to the R70 pump from a 2.2 HDI or a 3.0 BMW 530D. It’s important to use a good low mileage pump and not one that has been left standing without fuel in as the pump can corrode inside and cease, thus damaging the seals once it’s turned. The fuel pressure sensor 1920GW must be fitted, to get the engine to run with this pins 1&2 must be swapped in the wiring loom to the sensor. The turbo upgrade would ideally use a 52mm compressor with a VNT turbo, although a waste-gated turbo is also acceptable and easier to regulate with a mechanical boost controller. The electronic turbo control will be de-activated in the ecu software to avoid setup complications and to allow for external regulation. For VNT turbos the turbo can be controlled using a product called DigiBooster S. This uses electronic PID control to regulate boost with selectable strategies, a VNT turbo cannot be effectively controlled using only a ball and spring type mechanical boost controller. A ceramic paddle clutch is required to hold the 420Nm of torque.
Stage 3 vs stock
Power110 → 180 BHP
Torque250 → 420 Nm
Dyno graph for this stage coming soon.
Peugeot 607 2.0 HDI 110 Stage 1 + Full power Remap ( 150 BHP | 330 Nm )
The Stage 1++ remap adds to the gains of the stage 1+ remap and requires a complete straight through exhaust system and a high flow air filter. Peak power will be increased to 150 BHP and the maximum torque will be increased to 330Nm. Price:
- Program yourself with the MyGenius OBD tool, includes a Stage 1 Remap for just £300!
- Already have a programming tool? Use our Online remap service for just £150
- Send us your ECU - Postal Remap Service from £200
- Drive in or mobile remap from £350
1800 Bar fuel pressure sensor upgrade Part 1920GW
For vehicles running the upgraded R70 fuel pump wishing to push for a little extra top end power we can increase fuel pressure slightly. The stock sensor can only go to 1500 Bar so an upgraded sensor is required with part number 1920GW. Pins 1&2 must be swapped in the wiring loom in order to start the engine and a new calibration must be added via a remap. Injector calibrations in the stock ECU software run only until 1400 Bar, we will extend using our custom calibrations to 1800 bar. We recommend to run a max of 1600 Bar even with the uprated sensor, otherwise the extra work load on the fuel pump is too much. Price:
- £50 extra on top of remap cost – included with stage 3.
Bosch EDC15C2
Programming method
Programming Methods – OBD - MyGenius
Program from home over OBD using MyGenius. The only equipment you need is a battery charger to keep the vehicle power stable.
A laptop is required to initialise the MyGenius tool, it is not used during programming. The tool is standalone and powered from the OBD port.
Programming Methods – OBD - MPPS
This ECU can be OBD programmed with MPPS
Programming Methods – OBD - Kess
This ECU can be OBD programmed with Kess
More Peugeot
Other Peugeot remaps
Stage 1 incl. tool £330 Buy now