remap@hdi-tuning.co.uk Contact us Book appointment
Siemens SID202 SID206 remap

1.8 TDCI 75 BHP 2006 - 2013 Transit Connect

2006–2013 1.8 TDCI 75 Diesel Siemens SID202 SID206
Stock 75BHP 175Nm
Stage 1 125BHP 300Nm
Gain +50BHP +125Nm
Power (BHP) Torque (Nm) Stock Stage 1 dyno
150 350 120 280 90 210 60 140 30 70 0 0 10002000300040005000 RPM 300 Nm 125 BHP
Recommended tool Dimsport MyGenius: flash this car over OBD yourself
Stage 1 remap incl. OBD programming tool £330
Buy now · £330
  1. 1Read ECU over OBD
  2. 2Files sent by email
  3. 3Program yourself
  • All tuning is developed in house - over 15 years of experience
S1

Stage 1

125BHP+50
300Nm+125
Stage 1 is designed to run on standard components, with no hardware upgrades required. Our calibrations are developed and tested in house. We focus on smooth, strong, progressive power delivery.

Drivability, economy and reliability are key. We aim to maximise power while staying within the safe limits of your engine.

On vehicles with an automatic gearbox, you can rest assured that gear changes stay smooth and seamless. Because we correctly edit the torque model in the engine ECU, the transmission control unit (TCU) can make use of the extra low-end torque and calculate the optimal point to shift up or down. The TCU also shifts down less often when the torque model shows that power is available, which makes the vehicle much nicer to drive and you won't be interrupted by unwanted kickdown unless it's actually required or if you specifically hit the kickdown point.
Stage 1 vs stock
Power +67%
75 125 BHP
Stock 75S1 125 (+50)
Torque +71%
175 300 Nm
Stock 175S1 300 (+125)
See the dyno chart ↑
Siemens SID202 SID206

Programming method

Programming Methods – OBD programming or Bench Programming

There are three variants of the SID202/SID204/SID206 ECU. On Ford vehicles the ECU can be programmed over OBD by most tools like Kess V2. It’s also an option to remove the ECU and program on the bench over BDM (open ECU).

Programming via OBD SID206 with Kess V2

Programming via BDM SID206

The SID206 can be programmed direct to the ECU board through the BDM port. Obtain a suitable programming tool, we recommend Kess KTAG.
  • Order a suitable tool such as Kess KTAG or BDM100.
  • Install the tool to a reliable laptop.
  • The ECU must be removed from the vehicle, and then the tabs on the lid can be carefully pried open and the casing of the ECU removed.
  • Using a pogo spring probe connect to the ECU board, power the ECU to the ECU connector plugs as described by your programming tool.
  • ID the ECU and then take a read of the ECUs memories for a backup (please save separately, and not as a combined file). For EDC16C3 the performance maps are in the 1MB flash. For EDC16C34 the performance maps are stored in the 2MB flash memory.
  • Send payment through our webshop.
  • We will modify the software and send back to you. This normally takes less than 2 to 3 hours during working days.
  • Using the same tool, ID then write to the ECU. This will overwrite the ECUs memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about (You can always repair an ECU if you take a full BDM backup of all memories).
  • Straighten the lid on the ECU and seal with a little silicone.
  • Refit the ECU and start the engine.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!
  • More Ford

    Other Ford remaps