Siemens SID202 SID206 remap
1.8 TDCI 90 BHP 2006 - 2013 Transit Connect
2006–2013 1.8 TDCI 90 Diesel Siemens SID202 SID206
Stock 90BHP 235Nm
Stage 1 125BHP 300Nm
Gain +35BHP +65Nm
Stage 1 remap incl. OBD programming tool £330
Buy now · £330 - 1Read ECU over OBD
- 2Files sent by email
- 3Program yourself
- All tuning is developed in house - over 15 years of experience
S1
Stage 1
125BHP+35
300Nm+65
Stage 1 is designed to run on standard components, with no hardware upgrades required. Our calibrations are developed and tested in house. We focus on smooth, strong, progressive power delivery.
Drivability, economy and reliability are key. We aim to maximise power while staying within the safe limits of your engine.
On vehicles with an automatic gearbox, you can rest assured that gear changes stay smooth and seamless. Because we correctly edit the torque model in the engine ECU, the transmission control unit (TCU) can make use of the extra low-end torque and calculate the optimal point to shift up or down. The TCU also shifts down less often when the torque model shows that power is available, which makes the vehicle much nicer to drive and you won't be interrupted by unwanted kickdown unless it's actually required or if you specifically hit the kickdown point.
Drivability, economy and reliability are key. We aim to maximise power while staying within the safe limits of your engine.
On vehicles with an automatic gearbox, you can rest assured that gear changes stay smooth and seamless. Because we correctly edit the torque model in the engine ECU, the transmission control unit (TCU) can make use of the extra low-end torque and calculate the optimal point to shift up or down. The TCU also shifts down less often when the torque model shows that power is available, which makes the vehicle much nicer to drive and you won't be interrupted by unwanted kickdown unless it's actually required or if you specifically hit the kickdown point.
Stage 1 vs stock See the dyno chart ↑
Power +39%
90 125 BHP
Stock 90S1 125 (+35)
Torque +28%
235 300 Nm
Stock 235S1 300 (+65)
Siemens SID202 SID206
Programming method
Programming Methods – OBD programming or Bench Programming
There are three variants of the SID202/SID204/SID206 ECU. On Ford vehicles the ECU can be programmed over OBD by most tools like Kess V2. It’s also an option to remove the ECU and program on the bench over BDM (open ECU).
Programming via OBD SID206 with Kess V2
- Obtain a suitable programming tool; we recommend to use Dimsport MyGenius, you can also use Kess V2.
- Install the tool to a reliable laptop.
- Connect to the OBD port of your car, make sure you have backup chargers to the vehicle battery and the laptop battery.
- ID the ECU and then take a read of the ECUs flash memory.
- Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
- Send payment through our webshop.
- We will modify the software and send back to you. This normally takes less than 2 to 3 hours during working days.
- Using the same tool, ID then write to the ECU. This will overwrite the ECUs flash memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about.
- Let your engine warm up and then take the car for a spin, enjoy the extra power!
Programming via BDM SID206
The SID206 can be programmed direct to the ECU board through the BDM port. Obtain a suitable programming tool, we recommend Kess KTAG.
- Order a suitable tool such as Kess KTAG or BDM100.
- Install the tool to a reliable laptop.
- The ECU must be removed from the vehicle, and then the tabs on the lid can be carefully pried open and the casing of the ECU removed.
- Using a pogo spring probe connect to the ECU board, power the ECU to the ECU connector plugs as described by your programming tool.
- ID the ECU and then take a read of the ECUs memories for a backup (please save separately, and not as a combined file). For EDC16C3 the performance maps are in the 1MB flash. For EDC16C34 the performance maps are stored in the 2MB flash memory.
- Send payment through our webshop.
- We will modify the software and send back to you. This normally takes less than 2 to 3 hours during working days.
- Using the same tool, ID then write to the ECU. This will overwrite the ECUs memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about (You can always repair an ECU if you take a full BDM backup of all memories).
- Straighten the lid on the ECU and seal with a little silicone.
- Refit the ECU and start the engine.
- Let your engine warm up and then take the car for a spin, enjoy the extra power!
More Ford
Other Ford remaps
Transit Connect 1.5 TDCI 8V 75 2013 - 2019 75 → 126 BHP Transit Connect 1.5 TDCI 8V 95 2013 - 2019 95 → 126 BHP Transit Connect 1.8 TDCI 75 8V 2006 - 2013 75 → 125 BHP Transit Connect 1.6 TDCI 8V 115 2010 - 2015 115 → 148 BHP Transit Connect 1.6 TDCI 8V 75 2010 - 2015 75 → 148 BHP Transit Connect 1.6 TDCI 8V 95 2010 - 2015 95 → 148 BHP
Stage 1 incl. tool £330 Buy now