remap@hdi-tuning.co.uk Contact us Book appointment
Bosch EDC16C34 remap

1.6D 16V 110 BHP 2005 to 2010

2008–2010 1.6D 16V 110 Diesel Bosch EDC16C34
Stock 110BHP 245Nm
Stage 1 138BHP 280Nm
Gain +28BHP +35Nm
Power (BHP) Torque (Nm) Stock Stage 1 dyno
175 350 140 280 105 210 70 140 35 70 0 0 10002000300040005000 RPM 280 Nm 138 BHP
Stage 1 postal remap £200
Buy now · £200
  1. 1Order online and post us your ECU
  2. 2We remap it in house
  3. 3We post it back to you, ready to fit
  • All tuning is developed in house - over 15 years of experience
S1

Stage 1

DPF safe

138BHP+28
280Nm+35
Our stage 1 remap for the 1.6 16v 110 engine provides constant and increased torque through the entire rev range whilst remaining well within the safe limits of your clutch, dual mass flywheel and turbo charger. The torque delivery will be smooth and stable and it won’t drop off in the higher RPMs like the stock mapping, making your 1.6 HDI much more fun to drive.

We’ve designed our stage 1 remap to run cleanly and in unison with the DPF system, this means that there is no increased risk of clogging the DPF filter as long as regular long journeys are undertaken by the vehicle. Most customers also see a small economy gain during normal driving conditions.

The 1.6 16v engine is actaully a very reliable engine, but you must keep on top of servicing, change the oil more regularly for exxample 6k miles (10k km), oil is not expensive. If you have leaky injectors, don't leave them chuffing, the tar buildup pushes inside of the valve cover and gets in to the engine causing the common problems.

Keep it well mainintained and in perfect running order, this engine can easily go above 200 BHP with the right hardware.
Stage 1 vs stock
Power +25%
110 138 BHP
Stock 110S1 138 (+28)
Torque +14%
245 280 Nm
Stock 245S1 280 (+35)
See the dyno chart ↑
S1+

Stage 1+

Full Power Stage 1 +

143BHP+33
295Nm+50
Our full power Stage 1 remap takes power to 143BHP and torque to 295Nm. It allows for the addition of a performance downpipe and exhaust system. (For non DPF models you can go straight to this remap without any modifications).

Correct tuning of the 1.6 16v engine when fitted with a free-flowing downpipe, is more complex than you might think. Without a full recalibration of the turbo control strategy you'd likely end up with turbo failure. The HDI tuning approach is much very safe, we completely re-write the turbo control strategy to prevent overboost.

We have carefully calibrated our 1.6 16v remap to deliver optimum performance, respecting the stock hardware limitations of your vehicle. Through precise adjustments in turbo pre control strategies and turbo PID control maps, we ensure consistent boost and torque.
Power (BHP) Torque (Nm) Stock Stage 1+ dyno
175 350 140 280 105 210 70 140 35 70 0 0 10002000300040005000 RPM 295 Nm 143 BHP
S2

Stage 2

We skip our typical 'stage 2' remap on the 1.6 16v engine because there is already a factory fitted intercooler and the stock turbo charger does not respond well to boost pressure above the stage 1 settings. In this case jump straight to the Stage 3 options.
S3.2

Stage 3 · Option 2

Option 2 GTD1244VZ

155BHP+45
320Nm+75
The Stage 3 Option 2 upgrade uses a GTD1244VZ 819872 turbo charger from the 1.6 BlueHDI engine, in an unmodified form. The turbo is strong and it's designed to run at a higher pressure than your stock turbo. The GTD1244VZ uses fourth generation Garrett GTD technology which means earlier spool and better top end power.

This turbo fits directly on to the stock exhaust manifold. To run this remap we also require you to upgrade to the 0445110297 injectors, fit a 3.1 bar MAP sensor (Delphi PS10197), performance down pipe and an EGR blank (for track use only). It’s well worth while to fit an uprated intercooler, with this you'll get above 155 and usually end up closer to 160 BHP. Please see here for the GTD12 fitment guide.

Here's a dyno plot from a Fiesta 1.6 16v MK7 fitted with a GTD1244VZ and the 297 injectors and intercooler upgrade, exhaust etc. Power came out to 159.7 BHP and 350Nm.

Here's a Maha dyno plot from a C2 1.6 16v fitted with a GTD1244VZ and the 297 injectors using the standard intercooler with a downpipe. Power came out to 172 BHP and 337Nm.

Here's a Perf Expert Road dyno plot from a 207 1.6 16v with GTD1244VZ and the 297 injectors and intercooler upgrade. Power came out to 159.7 BHP and 350Nm. Perf Expert is not a real dyno so don't expect as much power as this.



Generally without an intercooler upgrade you'll get 153 to 155 BHP, with an intercooler upgrade these usually come out at 160 BHP and more torque too.
Power (BHP) Torque (Nm) Stock Stage 3 · Option 2 dyno
200 400 160 320 120 240 80 160 40 80 0 0 10002000300040005000 RPM 320 Nm 155 BHP
S3.3

Stage 3 · Option 3

Option 3

185BHP+75
370Nm+125
The next step up is to use a hybrid GTD12 turbo charger. The HDI Tuning GTD12 49mm hybrid uses a billet compressor with extended tip technology so the compressor behaves more like a 52mm wheel without the extra mass. This gives better spool up characteristics.

In order to use the HDI Tuning Stage 3 remap, you need to order the turbo charger from our store. Many companies build these slightly differently and we cannot gaurantee the same drive characteristics with an unknown turbo build.

To run this remap we also require you to upgrade to the 0445110297 injectors, fit a 3.1 Bar MAP sensor Delphi PS10197, performance down pipe and an EGR blank (for track use only). You will also need a large front mount intercooler with a straight through exhaust system of 2.5 inch. The clutch will need to be upgraded to at least a stage 2 Kevlar clutch, or better is a full stage 3 ceramic paddle clutch, or for better driveability try a hybrid friction plate stage 2.5 kit. Please see here for the full fitment guide.

Here's a dyno plot from a C2 1.6 16v 110fitted with a GTD12 hybrid and the 297 injectors, exhaust, intercooler 3.1 map sensor. Power came out to 187 BHP and 386Nm.

Here's a dyno plot from a Fiesta 1.6 16v MK6 fitted with a GTD12 hybrid and the 297 injectors, exhaust, intercooler 3.1 map sensor. Power came out to 179 BHP and 388Nm.

Here's a dyno plot from a 1.6 16v 75 BHP van with lots of miles on it, GTD12 49mm hybrid turbo, 297 injectors, 3.1 map sensor, larger intercooler, exhaust. This one made 161.95 WHEEL horse power, that's crazy, normal drag figures to get the flywheel torque are anywhere from 25 to 45 BHP for this engine, meaning this one pulled approx 185 BHP at the flywheel and 370Nm.

Here you can see that every dyno gives a different figure even with the same setup, the largest deviation is actually from the dyno and not the engine itself. If we tested all of these on the same dyno with the same set of wheel they would all make very similar results.

Power (BHP) Torque (Nm) Stock Stage 3 · Option 3 dyno
225 450 180 360 135 270 90 180 45 90 0 0 10002000300040005000 RPM 370 Nm 185 BHP
S4

Stage 4

205BHP+95
380Nm+135
HDI Tuning have developed a completely custom turbo manifold kit to fit the 1.6 16V engine. The turbo used is a TF035 from a 2.2 Mitsubishi engine with a very modern VNT system. This turbo offers excellent spool and crazy top end power. Upgrades required:
  • TF035 manifold
  • TF035 turbo
  • 3.1 bar or 4 bar MAP sensor
  • Turbo down pipe
  • 2.5 inch exhaust system
  • Large FMIC
  • 0445110297 injectors
  • The clutch will need to be upgraded to a full stage 3 ceramic paddle clutch.

Here's a dyno plot from a 207 1.6 16v 90 with the TF035 turbo, manifold, 297 injectors, 3.1 MAP sensor. Power came out to 205BHP

Here's a dyno plot from a Fiesta 1.6 16v 90 with the TF035 turbo, manifold, 297 injectors, 4 bar MAP sensor. Power came out to 230BHP on this one because we ran more boost, this one was at 2.2 bar which adds more power for sure, but also puts more stress on the engine so we typically recommend to stay at 2 bar (3bar aboslute)

Power (BHP) Torque (Nm) Stock Stage 4 dyno
250 450 200 360 150 270 100 180 50 90 0 0 10002000300040005000 RPM 389 Nm 205 BHP

Air Doser Delete

The butterfly/throttle and intercooler bypass valves in the intake can sometimes go wrong or leak. You can either disconnect it, or make a custom air doser delete pipe if it's leaking.

MAP Sensor upgrade

We can calibrate 3.1 bar and 4 bar MAP sensors in to the ECU. WE can even calibrate the 4 bar VAG sensor with the integrated temp sensor to your ECU if needed.

MAF Delete

On some setups we can run a MAF delete and AFR control is managed by MAP Sensor reading.

injector upgrade

We can calibrate higher flowing injectors to your ECU if there is an upgrade available.
Bosch EDC16C34

Programming method

Programming Methods – OBD programming or Bench Programming

There are two variants of ECU on the Volvo 1.6D 16V from 2005 to 2010. There are EDC16C31 and EDC16C34. We've found that for models from 2008 to 2010 with the EDC16C34 it is not possible to write over OBD, so instead the ECU must be removed. This is due to additional RSA checksums in the software which can only be corrected when using a full BDM dump of the software. Our postal remap service is popular for this ECU model. We have EDC16 bench service mode equipment which can program the full BDM dump without needing to open or dismantle the ECU which retains integrity of the seal and prevents water damage.

Programming via OBD EDC16C31

  • Obtain a suitable programming tool, we found an OBD write will only work with a genuine tool.
  • Install the tool to a reliable laptop.
  • Connect to the OBD port of your car, make sure you have backup chargers to the vehicle battery and the laptop battery.
  • ID the ECU and then take a read of the ECUs flash memory.
  • Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
  • Send payment through our webshop.
  • We will modify the software and send back to you. This normally takes less than 2 to 3 hours during working days.
  • Using the same tool, ID then write to the ECU. This will overwrite the ECUs flash memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!

Programming via BDM EDC16C31 & EDC16C34

  • Order a suitable BDM programming tool such as Kess KTAG
  • Install the tool to a reliable laptop.
  • The ECU must be removed from the vehicle, and then the tabs on the lid can be carefully pried open and the casing of the ECU removed.
  • Using a pogo spring probe connect to the ECU board, power the ECU to the ECU connector plugs as described by your programming tool.
  • ID the ECU and then take a read of the ECUs memories for a backup (please save separately, and not as a combined file).
  • Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
  • Send payment through our webshop.
  • We will modify the software and send back to you. This normally takes less than 2 to 3 hours during work days.
  • Using the same tool, ID then write to the ECU. This will overwrite the ECUs memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about (You can always repair an ECU if you take a full BDM backup of all memories).
  • Straighten the lid on the ECU and seal with a little silicone.
  • Refit the ECU and start the engine.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!
More Volvo

Other Volvo remaps