1.6D 16V 110 BHP 2005 to 2010
- 1Order online and post us your ECU
- 2We remap it in house
- 3We post it back to you, ready to fit
- All tuning is developed in house - over 15 years of experience
Stage 1
DPF safe
We’ve designed our stage 1 remap to run cleanly and in unison with the DPF system, this means that there is no increased risk of clogging the DPF filter as long as regular long journeys are undertaken by the vehicle. Most customers also see a small economy gain during normal driving conditions.
The 1.6 16v engine is actaully a very reliable engine, but you must keep on top of servicing, change the oil more regularly for exxample 6k miles (10k km), oil is not expensive. If you have leaky injectors, don't leave them chuffing, the tar buildup pushes inside of the valve cover and gets in to the engine causing the common problems.
Keep it well mainintained and in perfect running order, this engine can easily go above 200 BHP with the right hardware.
Stage 1+
Full Power Stage 1 +
Correct tuning of the 1.6 16v engine when fitted with a free-flowing downpipe, is more complex than you might think. Without a full recalibration of the turbo control strategy you'd likely end up with turbo failure. The HDI tuning approach is much very safe, we completely re-write the turbo control strategy to prevent overboost.
We have carefully calibrated our 1.6 16v remap to deliver optimum performance, respecting the stock hardware limitations of your vehicle. Through precise adjustments in turbo pre control strategies and turbo PID control maps, we ensure consistent boost and torque.
Stage 2
Stage 3 · Option 2
Option 2 GTD1244VZ
This turbo fits directly on to the stock exhaust manifold. To run this remap we also require you to upgrade to the 0445110297 injectors, fit a 3.1 bar MAP sensor (Delphi PS10197), performance down pipe and an EGR blank (for track use only). It’s well worth while to fit an uprated intercooler, with this you'll get above 155 and usually end up closer to 160 BHP. Please see here for the GTD12 fitment guide.
Here's a dyno plot from a Fiesta 1.6 16v MK7 fitted with a GTD1244VZ and the 297 injectors and intercooler upgrade, exhaust etc. Power came out to 159.7 BHP and 350Nm.
Here's a Maha dyno plot from a C2 1.6 16v fitted with a GTD1244VZ and the 297 injectors using the standard intercooler with a downpipe. Power came out to 172 BHP and 337Nm.
Here's a Perf Expert Road dyno plot from a 207 1.6 16v with GTD1244VZ and the 297 injectors and intercooler upgrade. Power came out to 159.7 BHP and 350Nm. Perf Expert is not a real dyno so don't expect as much power as this.
Generally without an intercooler upgrade you'll get 153 to 155 BHP, with an intercooler upgrade these usually come out at 160 BHP and more torque too.
Stage 3 · Option 3
Option 3
In order to use the HDI Tuning Stage 3 remap, you need to order the turbo charger from our store. Many companies build these slightly differently and we cannot gaurantee the same drive characteristics with an unknown turbo build.
To run this remap we also require you to upgrade to the 0445110297 injectors, fit a 3.1 Bar MAP sensor Delphi PS10197, performance down pipe and an EGR blank (for track use only). You will also need a large front mount intercooler with a straight through exhaust system of 2.5 inch. The clutch will need to be upgraded to at least a stage 2 Kevlar clutch, or better is a full stage 3 ceramic paddle clutch, or for better driveability try a hybrid friction plate stage 2.5 kit. Please see here for the full fitment guide.
Here's a dyno plot from a C2 1.6 16v 110fitted with a GTD12 hybrid and the 297 injectors, exhaust, intercooler 3.1 map sensor. Power came out to 187 BHP and 386Nm.
Here's a dyno plot from a Fiesta 1.6 16v MK6 fitted with a GTD12 hybrid and the 297 injectors, exhaust, intercooler 3.1 map sensor. Power came out to 179 BHP and 388Nm.
Here's a dyno plot from a 1.6 16v 75 BHP van with lots of miles on it, GTD12 49mm hybrid turbo, 297 injectors, 3.1 map sensor, larger intercooler, exhaust. This one made 161.95 WHEEL horse power, that's crazy, normal drag figures to get the flywheel torque are anywhere from 25 to 45 BHP for this engine, meaning this one pulled approx 185 BHP at the flywheel and 370Nm.
Here you can see that every dyno gives a different figure even with the same setup, the largest deviation is actually from the dyno and not the engine itself. If we tested all of these on the same dyno with the same set of wheel they would all make very similar results.
Stage 4
- TF035 manifold
- TF035 turbo
- 3.1 bar or 4 bar MAP sensor
- Turbo down pipe
- 2.5 inch exhaust system
- Large FMIC
- 0445110297 injectors
- The clutch will need to be upgraded to a full stage 3 ceramic paddle clutch.
Here's a dyno plot from a 207 1.6 16v 90 with the TF035 turbo, manifold, 297 injectors, 3.1 MAP sensor. Power came out to 205BHP
Here's a dyno plot from a Fiesta 1.6 16v 90 with the TF035 turbo, manifold, 297 injectors, 4 bar MAP sensor. Power came out to 230BHP on this one because we ran more boost, this one was at 2.2 bar which adds more power for sure, but also puts more stress on the engine so we typically recommend to stay at 2 bar (3bar aboslute)
Air Doser Delete
MAP Sensor upgrade
MAF Delete
injector upgrade
Programming method
Programming Methods – OBD programming or Bench Programming
Programming via OBD EDC16C31
- Obtain a suitable programming tool, we found an OBD write will only work with a genuine tool.
- Install the tool to a reliable laptop.
- Connect to the OBD port of your car, make sure you have backup chargers to the vehicle battery and the laptop battery.
- ID the ECU and then take a read of the ECUs flash memory.
- Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
- Send payment through our webshop.
- We will modify the software and send back to you. This normally takes less than 2 to 3 hours during working days.
- Using the same tool, ID then write to the ECU. This will overwrite the ECUs flash memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about.
- Let your engine warm up and then take the car for a spin, enjoy the extra power!
Programming via BDM EDC16C31 & EDC16C34
- Order a suitable BDM programming tool such as Kess KTAG
- Install the tool to a reliable laptop.
- The ECU must be removed from the vehicle, and then the tabs on the lid can be carefully pried open and the casing of the ECU removed.
- Using a pogo spring probe connect to the ECU board, power the ECU to the ECU connector plugs as described by your programming tool.
- ID the ECU and then take a read of the ECUs memories for a backup (please save separately, and not as a combined file).
- Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
- Send payment through our webshop.
- We will modify the software and send back to you. This normally takes less than 2 to 3 hours during work days.
- Using the same tool, ID then write to the ECU. This will overwrite the ECUs memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about (You can always repair an ECU if you take a full BDM backup of all memories).
- Straighten the lid on the ECU and seal with a little silicone.
- Refit the ECU and start the engine.
- Let your engine warm up and then take the car for a spin, enjoy the extra power!