remap@hdi-tuning.co.uk Contact us Book appointment
Delphi CRD2.35 remap

Sprinter 213 Delphi CRD2.35

2010–2013 213 OM651 Diesel Delphi CRD2.35
Stock 129BHP 305Nm
Stage 1 208BHP 460Nm
Gain +79BHP +155Nm
Power (BHP) Torque (Nm) Stock Stage 1 dyno
250 550 200 440 150 330 100 220 50 110 0 0 10002000300040005000 RPM 460 Nm 208 BHP
Recommended tool Dimsport MyGenius: flash this car over OBD yourself
Stage 1 remap incl. OBD programming tool £330
Buy now · £330
  1. 1Read ECU over OBD
  2. 2Files sent by email
  3. 3Program yourself
  • All tuning is developed in house - over 15 years of experience
S1

Stage 1

208BHP+79
460Nm+155
Stage 1 is designed to run on standard components, with no hardware upgrades required. Our calibrations are developed and tested in house. We focus on smooth, strong, progressive power delivery.

Drivability, economy and reliability are key. We aim to maximise power while staying within the safe limits of your engine.

On vehicles with an automatic gearbox, you can rest assured that gear changes stay smooth and seamless. Because we correctly edit the torque model in the engine ECU, the transmission control unit (TCU) can make use of the extra low-end torque and calculate the optimal point to shift up or down. The TCU also shifts down less often when the torque model shows that power is available, which makes the vehicle much nicer to drive and you won't be interrupted by unwanted kickdown unless it's actually required or if you specifically hit the kickdown point.
Stage 1 vs stock
Power +61%
129 208 BHP
Stock 129S1 208 (+79)
Torque +51%
305 460 Nm
Stock 305S1 460 (+155)
See the dyno chart ↑
Delphi CRD2.35

Programming method

Programming Methods – OBD programming or Bench Programming

Programming via OBD Delphi CRD2.35

  • Obtain a suitable programming tool: we recommend Kess V2, Bitbox or AutoTuner tools
  • Install the tool to a reliable laptop.
  • Connect to the OBD port of your car, make sure you have backup chargers to the vehicle battery and the laptop battery. This is VERY IMPORTANT, the sprinter can draw over 20Amps with the ignition on and can quickly go flat. We recommend to use a specialised battery support tool.
  • ID the ECU and then take a read of the ECUs flash memory.
  • Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
  • Send payment through our webshop.
  • We will modify the software and send back to you. This normally takes less than 2 to 3 hours during working days.
  • Using the same tool, ID then write to the ECU. This will overwrite the ECUs flash memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!

Programming via KTAG Delphi CRD2.35 (not recommended)

  • Order a suitable tool such as Kess KTAG, or much better is an original Flex motorsport tool.
  • This ECU is difficult to open and difficult to bench program, as such it is not advised for beginners.
  • Install the tool to a reliable laptop.
  • The ECU must be removed from the vehicle, and then the tabs on the lid can be carefully pried open and the casing of the ECU removed.
  • Using a pogo spring probe connect to the ECU board, power the ECU to the ECU connector plugs as described by your programming tool.
  • ID the ECU and then take a read of the ECUs memories for a backup (please save separately, and not as a combined file).
  • Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
  • Send payment through our webshop.
  • We will modify the software and send back to you. This normally takes less than 2 to 3 hours during work days.
  • Using the same tool, ID then write to the ECU. This will overwrite the ECUs memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about (You can always repair an ECU if you take a full BDM backup of all memories).
  • Straighten the lid on the ECU and seal with a little silicone.
  • Refit the ECU and start the engine.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!
More Mercedes

Other Mercedes remaps