Siemens SID805 remap
1.4 HDI 8V 54 BHP 2005 – 2014 Siemens SID805
2005–2014 1.4 HDI 8V 54 Diesel Siemens SID805
Stock 54BHP 130Nm
Stage 1 90BHP 200Nm
Gain +36BHP +70Nm
Stage 1 remap incl. OBD programming tool £330
Buy now · £330 - 1Read ECU over OBD
- 2Files sent by email
- 3Program yourself
- All tuning is developed in house - over 15 years of experience
S1
Stage 1
90BHP+36
200Nm+70
The 1.4 HDI 54 BHP variant comes from the factory with a much lower power output than other 1.4 HDI models, as the gearbox is rated to a lower torque level. Our remap stays within the safe limit of the gearbox, whilst still providing plenty of margin for safety.
The torque delivery is smooth and controlled and this is an important factor to look after your clutch and gearbox. The remap will make the car much more driveable; torque is increased through the entire rev range, and the engine will have enough power to pull at higher RPMs also. Thanks to the low weight of the C1 and 107 you'll be pleasantly surprised at the responsiveness and power from such a small engine. The stage 1 remap is designed to be safe for a standard engine with no modifications. The power curve will be continuous and will not drop off like the stock mapping, this means you have a longer usable rev range when you need it for over taking manoeuvres.
The gearbox is actually stronger than you might expect, we are running one of these with a GTD1244VZ turbo with 130 BHP and lots of torque and there have not been any gearbox problems.
The torque delivery is smooth and controlled and this is an important factor to look after your clutch and gearbox. The remap will make the car much more driveable; torque is increased through the entire rev range, and the engine will have enough power to pull at higher RPMs also. Thanks to the low weight of the C1 and 107 you'll be pleasantly surprised at the responsiveness and power from such a small engine. The stage 1 remap is designed to be safe for a standard engine with no modifications. The power curve will be continuous and will not drop off like the stock mapping, this means you have a longer usable rev range when you need it for over taking manoeuvres.
The gearbox is actually stronger than you might expect, we are running one of these with a GTD1244VZ turbo with 130 BHP and lots of torque and there have not been any gearbox problems.
Here's a dyno plot from a C2 1.4 HDI. Power came out to 90 BHP with a huge torque increase
Stage 1 vs stock See the dyno chart ↑
Power +67%
54 90 BHP
Stock 54S1 90 (+36)
Torque +54%
130 200 Nm
Stock 130S1 200 (+70)
S2
Stage 2
100BHP+46
220Nm+90
The 1.4 HDI 68 BHP variant has no factory fitted intercooler. The first step to going stage 2 is to install an intercooler and a boost gauge. Next you can increase boost to around 20 psi / 1.35 bar. Boost can be adjusted by altering the length of the actuator rod to the waste gate.
Exhaust upgrades are also recommended. Please be warned, the KP35 turbo is very small and it's not that resilient so you should not set too much boost pressure. It's better to upgrade to the TD02 turbo this is much stronger, in that case, jump straight to our Stage 3 Remap.
Exhaust upgrades are also recommended. Please be warned, the KP35 turbo is very small and it's not that resilient so you should not set too much boost pressure. It's better to upgrade to the TD02 turbo this is much stronger, in that case, jump straight to our Stage 3 Remap.
S3
Stage 3
120BHP+66
280Nm+150
For the HDI tuning stage 3 upgrade we need to fit the TD02 turbo charger and manifold from the 1.6 90 EU5 model (from 2010 models onwards). Infact, the 1.4 HDI EU5 model also comes with this turbo and an intercooler so you can use some of the parts. This is not such a straight forward upgrade but it’s worth the extra work, it also bolts on to the manifold, although if you use the entire manifold from the 1.6 this will flow better and matches the exhaust ports of the 1.4/1.6 engine exactly.
You will need to swap the actuator for a pressure actuator because the one that comes with the TD02 operates only from vacuum and not pressure. A pressure wastegate can be controlled by drilling/tapping a pressure feed into the side of the compressor just like the stock turbo, this then feeds in to the actautor and you adjust the length of the rod to set boost.
Next you must fit a front mounted intercooler, a boost gauge, full exhaust system and a ceramic paddle clutch to handle all that extra torque. (Another good option is to use a GTD1244VZ turbo from the 1.6 BlueHDI 120, the VNT can be regulated using an external PID controller called Digibooster-S, unfortunetely these are no longer manufactered so you will need some kind of alternative. This turbo will deliver much better low down boost and also some more top end boost.)
You will need to swap the actuator for a pressure actuator because the one that comes with the TD02 operates only from vacuum and not pressure. A pressure wastegate can be controlled by drilling/tapping a pressure feed into the side of the compressor just like the stock turbo, this then feeds in to the actautor and you adjust the length of the rod to set boost.
Next you must fit a front mounted intercooler, a boost gauge, full exhaust system and a ceramic paddle clutch to handle all that extra torque. (Another good option is to use a GTD1244VZ turbo from the 1.6 BlueHDI 120, the VNT can be regulated using an external PID controller called Digibooster-S, unfortunetely these are no longer manufactered so you will need some kind of alternative. This turbo will deliver much better low down boost and also some more top end boost.)
Here we have a dyno plot for a Peugeot 107 we worked on which started at 54BHP and came out to 139BHP and 327Nm using the GTD1244VZ turbo, so with the right turbo, a good amount of power is possible. The power output is proportional to how much boost you want to run. Obviously gettinga clutch that can hold the pwoer is difficult because the 1.4 uses a smaller diameter clutch than the 1.6.
Siemens SID805
Programming method
Programming Methods – OBD - MyGenius
Program from home over OBD using MyGenius. The only equipment you need is a battery charger to keep the vehicle power stable.
A laptop is required to initialise the MyGenius tool, it is not used during programming. The tool is standalone and powered from the OBD port.
Programming Methods – OBD - MPPS
This ECU can be OBD programmed with MPPS
Programming Methods – OBD - Kess
This ECU can be OBD programmed with Kess
Stage 1 incl. tool £330 Buy now